web-dev-qa-db-ja.com

Linuxが切断されたイーサネットインターフェイスを使い続けるのはなぜですか？

同じサブネットで使用される2つのイーサネットインターフェイスeth0とeth1を備えたLinuxシステムがあります。時々、インターフェースの1つが切断されている（ケーブルが抜かれている）場合でも、LinuxはそのIPアドレスを使用し続けることがあります。

たとえば、eth1が接続されているときにeth0が切断された場合、「iproget」コマンドがeth0をデフォルトのインターフェイスとして報告していることがわかります。

~ $ ip ro get 192.168.1.1

192.168.1.1 dev eth0  src 192.168.1.5

結果として、scpやpingなどのツールは、切断されたインターフェイスを使用して失敗します。

私の質問は、なぜLinuxが切断されたインターフェースを使い続けるのかということです。それらの使用を自動的に検出して停止するべきではありませんか？

linuxpingethernetrouteiproute
2
Sunny Yates

ARPフラックス！

sysctlパラメータarp_ignoreおよびarp_announceを必要に応じて設定する必要があります。

最初にこのコマンドをテストしてから、これらが機能する場合は、/etc/sysctl.confファイルに行を追加できます。

最初に次のコマンドを実行します。

# sysctl -a | grep net.ipv4.conf.*.arp

出力は次のようになります。

net.ipv4.conf.all.arp_accept = 0
net.ipv4.conf.all.arp_announce = 0
net.ipv4.conf.all.arp_filter = 0
net.ipv4.conf.all.arp_ignore = 0
net.ipv4.conf.all.arp_notify = 0
net.ipv4.conf.all.proxy_arp = 0
net.ipv4.conf.all.proxy_arp_pvlan = 0
net.ipv4.conf.default.arp_accept = 0
net.ipv4.conf.default.arp_announce = 0
net.ipv4.conf.default.arp_filter = 0
net.ipv4.conf.default.arp_ignore = 0
net.ipv4.conf.default.arp_notify = 0
net.ipv4.conf.default.proxy_arp = 0
net.ipv4.conf.default.proxy_arp_pvlan = 0
net.ipv4.conf.eth0.arp_accept = 0
net.ipv4.conf.eth0.arp_announce = 0
net.ipv4.conf.eth0.arp_filter = 0
net.ipv4.conf.eth0.arp_ignore = 0
net.ipv4.conf.eth0.arp_notify = 0
net.ipv4.conf.eth0.proxy_arp = 0
net.ipv4.conf.eth0.proxy_arp_pvlan = 0
net.ipv4.conf.eth1.arp_accept = 0
net.ipv4.conf.eth1.arp_announce = 0
net.ipv4.conf.eth1.arp_filter = 0
net.ipv4.conf.eth1.arp_ignore = 0
net.ipv4.conf.eth1.arp_notify = 0
net.ipv4.conf.eth1.proxy_arp = 0
net.ipv4.conf.eth1.proxy_arp_pvlan = 0
net.ipv4.conf.lo.arp_accept = 0
net.ipv4.conf.lo.arp_announce = 0
net.ipv4.conf.lo.arp_filter = 0
net.ipv4.conf.lo.arp_ignore = 0
net.ipv4.conf.lo.arp_notify = 0
net.ipv4.conf.lo.proxy_arp = 0
net.ipv4.conf.lo.proxy_arp_pvlan = 0

次に、次のコマンドを実行します。

# sysctl -w net.ipv4.conf.all.arp_ignore=1
# sysctl -w net.ipv4.conf.all.arp_announce=2

引き続きこのコマンドを実行して、変更を確認してください

# sysctl -a | grep net.ipv4.conf.*.arp

変更を加えた次のようなものが表示されるはずです。

net.ipv4.conf.all.arp_accept = 0
net.ipv4.conf.all.arp_announce = 1
net.ipv4.conf.all.arp_filter = 0
net.ipv4.conf.all.arp_ignore = 1
net.ipv4.conf.all.arp_notify = 0
net.ipv4.conf.all.proxy_arp = 0
net.ipv4.conf.all.proxy_arp_pvlan = 0
net.ipv4.conf.default.arp_accept = 0
net.ipv4.conf.default.arp_announce = 0
net.ipv4.conf.default.arp_filter = 0
net.ipv4.conf.default.arp_ignore = 0
net.ipv4.conf.default.arp_notify = 0
net.ipv4.conf.default.proxy_arp = 0
net.ipv4.conf.default.proxy_arp_pvlan = 0
net.ipv4.conf.eth0.arp_accept = 0
net.ipv4.conf.eth0.arp_announce = 0
net.ipv4.conf.eth0.arp_filter = 0
net.ipv4.conf.eth0.arp_ignore = 0
net.ipv4.conf.eth0.arp_notify = 0
net.ipv4.conf.eth0.proxy_arp = 0
net.ipv4.conf.eth0.proxy_arp_pvlan = 0
net.ipv4.conf.eth1.arp_accept = 0
net.ipv4.conf.eth1.arp_announce = 0
net.ipv4.conf.eth1.arp_filter = 0
net.ipv4.conf.eth1.arp_ignore = 0
net.ipv4.conf.eth1.arp_notify = 0
net.ipv4.conf.eth1.proxy_arp = 0
net.ipv4.conf.eth1.proxy_arp_pvlan = 0
net.ipv4.conf.lo.arp_accept = 0
net.ipv4.conf.lo.arp_announce = 0
net.ipv4.conf.lo.arp_filter = 0
net.ipv4.conf.lo.arp_ignore = 0
net.ipv4.conf.lo.arp_notify = 0
net.ipv4.conf.lo.proxy_arp = 0
net.ipv4.conf.lo.proxy_arp_pvlan = 0

または、必要に応じて値を変更できます。

arp_announce

arp_announce - INTEGER
    Define different restriction levels for announcing the local
    source IP address from IP packets in ARP requests sent on
    interface:
    0 - (default) Use any local address, configured on any interface
    1 - Try to avoid local addresses that are not in the target's
    subnet for this interface. This mode is useful when target
    hosts reachable via this interface require the source IP
    address in ARP requests to be part of their logical network
    configured on the receiving interface. When we generate the
    request we will check all our subnets that include the
    target IP and will preserve the source address if it is from
    such subnet. If there is no such subnet we select source
    address according to the rules for level 2.
    2 - Always use the best local address for this target.
    In this mode we ignore the source address in the IP packet
    and try to select local address that we prefer for talks with
    the target Host. Such local address is selected by looking
    for primary IP addresses on all our subnets on the outgoing
    interface that include the target IP address. If no suitable
    local address is found we select the first local address
    we have on the outgoing interface or on all other interfaces,
    with the hope we will receive reply for our request and
    even sometimes no matter the source IP address we announce.

    The max value from conf/{all,interface}/arp_announce is used.

    Increasing the restriction level gives more chance for
    receiving answer from the resolved target while decreasing
    the level announces more valid sender's information.

arp_ignore

arp_ignore - INTEGER
    Define different modes for sending replies in response to
    received ARP requests that resolve local target IP addresses:
    0 - (default): reply for any local target IP address, configured
    on any interface
    1 - reply only if the target IP address is local address
    configured on the incoming interface
    2 - reply only if the target IP address is local address
    configured on the incoming interface and both with the
    sender's IP address are part from same subnet on this interface
    3 - do not reply for local addresses configured with scope Host,
    only resolutions for global and link addresses are replied
    4-7 - reserved
    8 - do not reply for all local addresses

    The max value from conf/{all,interface}/arp_ignore is used
    when ARP request is received on the {interface}

満足したら、これらの2行を/etc/sysctl.confに追加する必要があります。

# cp /etc/sysctl.conf /etc/sysctl.confBKP

# echo "net.ipv4.conf.all.arp_ignore=1" >> /etc/sysctl.conf

# echo s"net.ipv4.conf.all.arp_announce=2" >> /etc/sysctl.conf

参考のためにこれらのリンク：

ARPフラックス

ARPを使用

この助けを願っています。

1
C. La Mosca